Home - Products - Formulation - Details
Pouring Of Transformer Component

Pouring Of Transformer Component

HY 8125 Epoxy Casting System For 10–35 kV medium- and high-voltage indoor instrument transformers 01 Mixing Ratio 02 Application HY8125A / HY8125B is recommended for 10–35 kV medium-voltage and high-voltage indoor instrument transformers. 03 Operating Method Casting process 04...

Description

HY8125

Epoxy Casting System

For 10–35 kV medium- and high-voltage indoor instrument transformers

 

01 Mixing Ratio

Component

Parts

HY8125A Epoxy Resin

100 pbw

HY8125B Curing Agent

100 pbw

Silica Filler

300–350 pbw

 

02 Application

HY8125A / HY8125B is recommended for 10–35 kV medium-voltage and high-voltage indoor instrument transformers.

 

03 Operating Method

Casting process

 

04 Characteristics

● Extremely low initial mixed viscosity

● Excellent mechanical and electrical properties

● Adjustable filler content and crack-resistance performance

 

05 Physical Properties of Single Components

HY8125A Modified Liquid Epoxy Resin

Parameter

Value

Viscosity at 25 °C, mPa·s [ISO 2555]

3000–6000

Non-volatile content, wt%

100

Density at 25 °C, g/cm³ [ISO 1675]

1.10–1.20

Shelf life at 25 °C (sealed container), months

12

Note: To prevent moisture absorption, store the epoxy resin in sealed containers at ambient temperature (approx. 6–35 °C). Typical values shall not be regarded as product specifications.

 

YH8125B Liquid Modified Anhydride Curing Agent

Parameter

Value

Viscosity at 25 °C, mPa·s [ISO 2555]

400–800

Density at 25 °C, g/cm³ [ISO 1675]

1.15–1.25

Vapour pressure at 20 °C, Pa

< 1

Shelf life at 25 °C (sealed container), months

12

Note: Anhydride curing agents are highly moisture-sensitive. Excessive moisture may alter the reactivity of the system and consequently degrade final product performance. Store anhydride curing agents in sealed containers at ambient temperature (approx. 6–35 °C). Typical values shall not be regarded as product specifications.

 

06 Process Procedure

Please contact our technical service staff for further information.

 

07 Processing Conditions

Please contact our technical service staff for further information. Demoulding time and post-curing cycle shall be determined according to specific product design and manufacturing process. For more details, please contact our technical service personnel.

 

08 Process Parameters (Guideline Values)

Component

Parts

HY8125A Epoxy Resin

100 parts by weight

HY8125B Curing Agent

100 parts by weight

Silica Filler

330 parts by weight

Notice: The grade and quality of the silica filler will affect process parameters such as initial mixed viscosity and reactivity. Typical values shall not be regarded as product specifications.

 

09 Mechanical & Physical Properties (Guideline Values)

Specimen post-curing condition: 10–12 h @ 120–130 °C

Tensile Properties [ISO 527]

Parameter

Value

Tensile strength at 25 °C, MPa

70–90

Elongation at break, %

1.0–1.5

Tensile modulus E, MPa

10 000–12 000

Flexural, Thermal and Electrical Properties

Parameter

Value

Flexural strength at 25 °C, MPa [ISO 178]

120–140

Impact strength, kJ/m² [ISO 179]

≥ 12

Coefficient of linear thermal expansion (30–80 °C), ppm/K

35–40

Thermal conductivity, W/(m·K)

0.8–1.0

Water absorption (10 days @ 23 °C), % [ISO 62]

0.1–0.2

Dielectric strength at 25 °C, kV/mm [IEC 60243-1]

30–35

Volume resistivity at 25 °C, Ω·cm [IEC 60093]

10¹³–10¹⁵

Dielectric constant ε′ [IEC 60250]

4.0–5.0

Dielectric loss tan δ at 50 Hz, 25 °C [IEC 60250]

< 0.025

 

10 Industrial Hygiene

Comply with industrial hygiene standards during handling and processing. Refer to the corresponding Safety Data Sheet and Hygiene Protection Measures for Plastic Products Handling for additional information.

 

11 Operational Protection Measures

Workplace Safety

Protective clothing, gloves, arm protection, safety goggles / safety glasses and a dust-proof respirator are required when skin contact is possible.

Skin Protection

● Apply barrier cream on exposed skin before work.

● Apply repairing or nourishing cream after washing hands.

● For skin contamination: wipe off excess material with absorbent paper, rinse with warm water and alkali-free soap, then dry with disposable towels. Do NOT use solvents.

Workshop Environment

Cover workbenches and chairs with light-coloured paper; use disposable beakers and similar utensils. Absorb spills with sawdust or waste cotton rags and collect in plastic woven baskets.

Ventilation

Workshop ventilation: 3–5 air changes per hour. Provide a local exhaust fan at workstations. Operators shall avoid vapour inhalation.

 

12 First-Aid Measures

In case of eye contact with resin, curing agent or casting compound: flush the eyes immediately with plenty of clean running water for 10–15 minutes and seek medical attention. For skin splashes or contamination: wipe off the material first and rinse the affected area with running water as described above. Seek medical help in case of severe irritation or burns. Remove contaminated clothing promptly. If discomfort occurs from vapour inhalation, move the person to fresh air immediately. Seek medical advice if in doubt.

 

Disclaimer

The data in this datasheet are typical laboratory guideline values and shall not be regarded as product specifications or guaranteed values. Actual performance depends on formulation, filler grade, process conditions and part design. Please consult the corresponding Safety Data Sheet (SDS) before use. Zhejiang Heyi Chemical Co., Ltd reserves the right to revise the technical information of its products.

Hot Tags: pouring of transformer component, China pouring of transformer component manufacturers, suppliers, factory

Previous:No Information

You Might Also Like

Shopping Bags